Skip to main content
Sump Pump Failure icon

Sump Pump Failure

Sump pump not activating, running continuously, or making unusual noises.

By Ray Smith

How Serious Is It?

  • ●
    Pump makes a humming noise but no water is exiting — Jammed impeller, mechanical failure, or frozen/clogged exterior discharge pipe
  • ●
    Water level rises over the pump but it does not turn on — Stuck float switch, burned-out motor, or power failure during a storm
  • ●
    Repeated tripping of the circuit breaker when the pump tries to start — Electrical short, burned-out motor, or heavy mechanical resistance inside the pump
  • ●
    Pump runs continuously without stopping — Missing or broken check valve causing water to flow back into the pit, or pump is undersized for the water volume
  • ●
    Sudden loud mechanical noises or grinding sounds from the basin — Internal component failure or debris caught in the impeller

Questions to Ask Yourself

  • ?How old is the pump — do you know the installation date or have the manual?
  • ?Does the pump activate when you manually lift the float switch or pour water in the pit?
  • ?Is the discharge line clear and flowing outside, or could it be frozen or blocked?
  • ?Do you have a battery backup system, and when was the battery last replaced?

Typical Cost Range

$150–$900. Minor repairs like a switch replacement cost around $150; installing a high-quality primary pump with a battery backup system can reach $900+.

DIY or Hire a Pro?

Testing the float switch and checking the discharge line are straightforward DIY checks. Replacing a submersible pump is within reach for a confident DIYer — manufacturer instructions are clear and the plumbing is minimal. However, if the pit itself is cracked, undersized, or if water is entering faster than any pump can handle, that requires a professional system assessment.

Common Misdiagnoses

  • ⚠Assuming the pump itself is broken when the actual issue is a frozen or blocked outdoor discharge line preventing water from leaving the system.
  • ⚠Replacing the entire pump unit when only the tethered float switch is stuck against the side of the basin.
  • ⚠Thinking a standard sump pump will work during a severe storm without realizing a power outage will render it useless without a battery backup.
Emergency

Water is rapidly rising in the pit during a storm and threatening to flood the basement; immediate manual pumping or emergency replacement needed.

Urgent

Pump is cycling excessively or making grinding noises; needs replacement or repair before the next rain event.

Can Plan Ahead

Installing a battery or water-powered backup system, or performing annual maintenance and testing.

Solutions for This Problem

What to Do Right Now

  1. 1. Check the power supply first — confirm the outlet has power (test with a lamp) and the GFCI has not tripped.
  2. 2. Manually lift the float switch to see if the pump activates — a stuck float is the most common failure cause.
  3. 3. Inspect the discharge line outside the house — a frozen or blocked pipe will prevent the pump from moving water even if it runs.
  4. 4. If the pump hums but does not pump, the impeller is likely jammed — unplug it before attempting to clear debris.
  5. 5. If the pit is filling and the pump is dead, use a wet/dry vac or portable utility pump as an emergency backup while you arrange replacement.
Sump pump troubleshooting diagram showing common failure points: float switch, discharge line, check valve, GFCI outlet, and impeller
Diagram: Sump Pump Failure

370

Sump Pump Installation & Repair contractors

280

Cities covered

Browse Sump Pump Installation & Repair Contractors

Find Sump Pump Installation & Repair Contractors Near You

370 contractors across 280 cities

Helpful Guides

Top Rated Contractors for This Issue

Ready to Hire? Find Sump Pump Installation & Repair Contractors Near You

370 contractors across 280 cities

Frequently Asked Questions

How serious is sump pump not working?

Pump makes a humming noise but no water is exiting: Jammed impeller, mechanical failure, or frozen/clogged exterior discharge pipe. Water level rises over the pump but it does not turn on: Stuck float switch, burned-out motor, or power failure during a storm. Repeated tripping of the circuit breaker when the pump tries to start: Electrical short, burned-out motor, or heavy mechanical resistance inside the pump. Pump runs continuously without stopping: Missing or broken check valve causing water to flow back into the pit, or pump is undersized for the water volume. Sudden loud mechanical noises or grinding sounds from the basin: Internal component failure or debris caught in the impeller.

How much does it cost to fix sump pump not working?

$150–$900. Minor repairs like a switch replacement cost around $150; installing a high-quality primary pump with a battery backup system can reach $900+.

Can I fix sump pump not working myself?

Testing the float switch and checking the discharge line are straightforward DIY checks. Replacing a submersible pump is within reach for a confident DIYer — manufacturer instructions are clear and the plumbing is minimal. However, if the pit itself is cracked, undersized, or if water is entering faster than any pump can handle, that requires a professional system assessment.

Sources

  1. simplywaterheaters.com
  2. pushleads.com
  3. chicagohomeinspector.com

About the Author

RS

Ray Smith

Ray Smith researches and writes guides for DryBasementHub, a contractor directory covering 18 US states. He is not a licensed contractor or building scientist; all technical claims on the site cite primary sources, industry datasets, or aggregated contractor pricing references.

Other Basement Problems